"TROUBLE SHOOTING ''
error machine
error code
cause
Abatement
211
Stop position does not fit the red line
Check the main shaft of motor / encoder / belt motors
Slide into position 100 '
212
The position of the needle being dropped
Put on a posii to correct / position 100 '
221
The position of the frame to the right over the edge
Movement back towards the left frame
do not pass the limit
222
The position of the frame to the left over the limit
Movement back towards the right frame
do not pass the limit
223
Position the frame up over the limit
Movement back frame downwardly
do not pass the limit
224
Position the frame down over the limit
Back frame upward movement
do not pass the limit
225
Position frame + x-axis (right) passes the limit (for machine cap)
Movement of the frame to the right place
251
Lubricating oil in the tank runs out
Refill the oil in the tank
281
Time replace needle / color over 15detik
Adjust the needle position manual / rotating motor
291
Yarn breaking / broken needle
Attach the yarn dang anti needle breakage
293
Yarn lifeboat end / consumables
Check or replace the lifeboat thread
2B1
Not biased read diskette or tape design
Check the data design (design order)
2B2
Not in accordance with the format machines
Check the data design (design order)
2B3
Data is not entirely legible
Check the data design (design order)
2B4
The function code in the design wrong
Check the data design (design order)
2B5
Sequins data is not normal
Check the data design (design order)
2B6
Serial I / F is not installed
Check the cable ssambungan in TFD
2B7
Data sets unfinished or incomplete
Perform a complete set of data
2B8
Error when reading data buffer
Check in setting reader TFD
2B9
Time entering data can not enter
Check the CPU card or card panel
2BA
Capacity memory exhausted
Remove one of the main designs that are not needed
2BB
Stitch in time the data is already depleted
Stop command repetition stitch
2BC
No. Design nothing in the machine's memory
Look up the correct design or re-record
2BE
In function of satin, boring, sequin yet in seting
Setinglah first if the puncture would be used
2C1
The time machine in star / stop
panel is being used
Cancel pengoprasian first panel
2C2
One pengprasian setting panel
Fix pengoprasian setting panel
2C6
The machine is made the turn bobbin
changer
Machines do not run on time change bobbins
2CB
Design images are too large over the limit tract
Adjust the machine capabilities
(Width tract)
2E3
Electricity is off when the engine is running
(Including the use of emergencystop)
Use pasilitas power resumes to return to the correct position
311
Encoder does not respond + member 5detik
Or belt motors dynamo defective / fox
Check rotary encoder, check belt
Dynamo or main shaft drivers
312
Signal of encoder z no
Check if the encoder lines replace damaged
316
Dinamo is not the way
Check the motor belt
321
The frame can not move
Check or replace the driver unit
322
Frame x-axis is not the way
Check or replace the driver unit
323
Frame y-axis is not the way
Check or replace the driver unit
331
Bobbin charger is not normal
Check / setting bobbin section Canger
352
Sequins function is not normal
Check or replace the card Sequins
382
Color change is not moving
Check the needle position sensor
or replace the motor color change
383
Signal to turn the color does not exist
Check the potentiometer (position sensor needle)
384
Replace the sensor signal no color
Check the photo-interrupter
3A1
Movers no thread cut signal
Priksa join or replace the card
3A6
The position is not correct thread cutter
Check the position sensor thread cutter / movable knife
3A8
Tread driver holding no signal
Check head card
3B5
Signal panel between CPU card and card, CPU card
And inverter, or between CPU card, card join, and no head card
Turn off the engine and check the cable connection
Among these card_card
3D1
Volt battery is weak
Turn on the machine and then setting the parameters and input designs
3D3
Power supply is not normal
Check the cable connection
or replace transformers
3D4
Data check sum is not detected
Change CPU cardnya
3D5
A ram check sum data is not normal
Reinstall the program if there are any engine system or fix the panel cardnya
B01
Time to enter any type floppy format
Reformat to type the correct capacity
B02
Record diskette of the machine can not enter
Try again if you keep guns could try to replace the use of other diskettes
B03
Protect the diskette active
Go to protect diketnya
B04
Floppy was not installed in fdd
Put a floppy
BC1
The data unreadable floppy
Replace with another designnya
BC2
Time recording design to an existing machine the same
Rename designnya
BC4
Design that is recorded to a diskette no
re-record
BC5
The capacity of a floppy disk is full
Wear new diskette
C01
Problem about FDD
Check the cord is damaged or if Fddnya replace with new.
error code
|
cause
|
Abatement
|
211
|
Stop position does not fit the red line
|
Check the main shaft of motor / encoder / belt motors
Slide into position 100 '
|
212
|
The position of the needle being dropped
|
Put on a posii to correct / position 100 '
|
221
|
The position of the frame to the right over the edge
|
Movement back towards the left frame
do not pass the limit
|
222
|
The position of the frame to the left over the limit
|
Movement back towards the right frame
do not pass the limit
|
223
|
Position the frame up over the limit
|
Movement back frame downwardly
do not pass the limit
|
224
|
Position the frame down over the limit
|
Back frame upward movement
do not pass the limit
|
225
|
Position frame + x-axis (right) passes the limit (for machine cap)
|
Movement of the frame to the right place
|
251
|
Lubricating oil in the tank runs out
|
Refill the oil in the tank
|
281
|
Time replace needle / color over 15detik
|
Adjust the needle position manual / rotating motor
|
291
|
Yarn breaking / broken needle
|
Attach the yarn dang anti needle breakage
|
293
|
Yarn lifeboat end / consumables
|
Check or replace the lifeboat thread
|
2B1
|
Not biased read diskette or tape design
|
Check the data design (design order)
|
2B2
|
Not in accordance with the format machines
|
Check the data design (design order)
|
2B3
|
Data is not entirely legible
|
Check the data design (design order)
|
2B4
|
The function code in the design wrong
|
Check the data design (design order)
|
2B5
|
Sequins data is not normal
|
Check the data design (design order)
|
2B6
|
Serial I / F is not installed
|
Check the cable ssambungan in TFD
|
2B7
|
Data sets unfinished or incomplete
|
Perform a complete set of data
|
2B8
|
Error when reading data buffer
|
Check in setting reader TFD
|
2B9
|
Time entering data can not enter
|
Check the CPU card or card panel
|
2BA
|
Capacity memory exhausted
|
Remove one of the main designs that are not needed
|
2BB
|
Stitch in time the data is already depleted
|
Stop command repetition stitch
|
2BC
|
No. Design nothing in the machine's memory
|
Look up the correct design or re-record
|
2BE
|
In function of satin, boring, sequin yet in seting
|
Setinglah first if the puncture would be used
|
2C1
|
The time machine in star / stop
panel is being used
|
Cancel pengoprasian first panel
|
2C2
|
One pengprasian setting panel
|
Fix pengoprasian setting panel
|
2C6
|
The machine is made the turn bobbin
changer
|
Machines do not run on time change bobbins
|
2CB
|
Design images are too large over the limit tract
|
Adjust the machine capabilities
(Width tract)
|
2E3
|
Electricity is off when the engine is running
(Including the use of emergencystop)
|
Use pasilitas power resumes to return to the correct position
|
311
|
Encoder does not respond + member 5detik
Or belt motors dynamo defective / fox
|
Check rotary encoder, check belt
Dynamo or main shaft drivers
|
312
|
Signal of encoder z no
|
Check if the encoder lines replace damaged
|
316
|
Dinamo is not the way
|
Check the motor belt
|
321
|
The frame can not move
|
Check or replace the driver unit
|
322
|
Frame x-axis is not the way
|
Check or replace the driver unit
|
323
|
Frame y-axis is not the way
|
Check or replace the driver unit
|
331
|
Bobbin charger is not normal
|
Check / setting bobbin section Canger
|
352
|
Sequins function is not normal
|
Check or replace the card Sequins
|
382
|
Color change is not moving
|
Check the needle position sensor
or replace the motor color change
|
383
|
Signal to turn the color does not exist
|
Check the potentiometer (position sensor needle)
|
384
|
Replace the sensor signal no color
|
Check the photo-interrupter
|
3A1
|
Movers no thread cut signal
|
Priksa join or replace the card
|
3A6
|
The position is not correct thread cutter
|
Check the position sensor thread cutter / movable knife
|
3A8
|
Tread driver holding no signal
|
Check head card
|
3B5
|
Signal panel between CPU card and card, CPU card
And inverter, or between CPU card, card join, and no head card
|
Turn off the engine and check the cable connection
Among these card_card
|
3D1
|
Volt battery is weak
|
Turn on the machine and then setting the parameters and input designs
|
3D3
|
Power supply is not normal
|
Check the cable connection
or replace transformers
|
3D4
|
Data check sum is not detected
|
Change CPU cardnya
|
3D5
|
A ram check sum data is not normal
|
Reinstall the program if there are any engine system or fix the panel cardnya
|
B01
|
Time to enter any type floppy format
|
Reformat to type the correct capacity
|
B02
|
Record diskette of the machine can not enter
|
Try again if you keep guns could try to replace the use of other diskettes
|
B03
|
Protect the diskette active
|
Go to protect diketnya
|
B04
|
Floppy was not installed in fdd
|
Put a floppy
|
BC1
|
The data unreadable floppy
|
Replace with another designnya
|
BC2
|
Time recording design to an existing machine the same
|
Rename designnya
|
BC4
|
Design that is recorded to a diskette no
|
re-record
|
BC5
|
The capacity of a floppy disk is full
|
Wear new diskette
|
C01
|
Problem about FDD
|
Check the cord is damaged or if Fddnya replace with new.
|
============================
"TROUBLE SHOOTING''
Error mesin
Code eror
|
Penyebabnya
|
Penanggulangannya
|
211
|
Stop posisi tidak pas garis merah
|
Periksa main shaft motor/encoder/belt motor
Geserkan ke posisi 100’
|
212
|
Posisi jarum sedang turun
|
Putarkan ke posii yang benar /posisi 100’
|
221
|
Posisi frame ke kanan melewati batas
|
Gerakan kembali frame kearah kiri
jangan melewati batasnya
|
222
|
Posisi frame ke kiri melewati batas
|
Gerakan kembali frame kearah kanan
jangan melewati batasnya
|
223
|
Posisi frame ke atas melewati batas
|
Gerakan kembali frame kearah bawah
jangan melewati batasnya
|
224
|
Posisi frame ke bawah melewati batas
|
Gerakan kembali frame kearah atas
jangan melewati batasnya
|
225
|
Posisi frame sumbu +x (kanan) melewati batasnya (untuk mesin topi)
|
Gerakan frame ke tempat yang benar
|
251
|
Minyak pelumas di tank habis
|
Isi kembali oli di tank
|
281
|
Waktu ganti jarum / warna lebih dari 15detik
|
Atur posisi jarum manual /memutarkan motor penggerak
|
291
|
Benang putus / jarum patah
|
Pasang benangnya dang anti jarum yang patahnya
|
293
|
Benang sekoci putus / habis
|
Periksa benang sekoci atau ganti
|
2B1
|
Tidak bias baca disket atau pita design
|
Periksa data design (design rusak)
|
2B2
|
Tidak sesuai dengan format mesin
|
Periksa data design (design rusak)
|
2B3
|
Data tidak terbaca seluruhnya
|
Periksa data design (design rusak)
|
2B4
|
Fungsi code pada design salah
|
Periksa data design (design rusak)
|
2B5
|
Data sequin tidak normal
|
Periksa data design (design rusak)
|
2B6
|
Serial I/F belum terpasang
|
Periksa ssambungan kabel di TFD
|
2B7
|
Data set belum selesai atau belum lengkap
|
Lakukan data set yang lengkap
|
2B8
|
Eror pada waktu buffer pembacaan data
|
Periksa di setting reader TFD
|
2B9
|
Waktu memasukan data tidak bisa masuk
|
Periksa CPU card atau panel card
|
2BA
|
Capasitas memori habis
|
Hapus salahsatu designs yang sudah tidak perlukan
|
2BB
|
Waktu data stitch di ulang sudah habis
|
Hentikan perintah pengulangan stitch
|
2BC
|
No Design tidak ada di memori mesin
|
Cari no design yang benar atau rekam ulang
|
2BE
|
Pada fungsi satin,boring,sequin belum di seting
|
Setinglah dulu kalau pungsi tersebut mau di gunakan
|
2C1
|
Waktu mesin di star / stop
panel sedang digunakan
|
Batalkan pengoprasian panel terlebih dahulu
|
2C2
|
Salah pengprasian seting panel
|
Perbaiki pengoprasian seting panel
|
2C6
|
Mesin sedang melakukan pergantian bobbin
changer
|
Mesin jangan di jalankan di waktu pergantian bobbin
|
2CB
|
Design gambar terlalu besar melewati batas bidangan
|
Sesuaikan dengan kemampuan mesin
(lebarnya bidangan)
|
2E3
|
Listrik mati ketika mesin sedang berjalan
(termasuk dengan penggunaan emergencystop)
|
Gunakan pasilitas power resume untuk mengembalikan ke posisi yang benar
|
311
|
Encoder tidak member respon +5detik
Atau belt motor dynamo rusak/rubah
|
Periksa rotary encoder,periksa belt
Dynamo atau main shaft drivernya
|
312
|
Signal dari encoder z tidak ada
|
Periksa jalur encodernya jika rusak ganti
|
316
|
Dinamo tidak jalan
|
Periksa belt motor
|
321
|
Frame tidak bisa bergerak
|
Periksa atau ganti driver unit
|
322
|
Frame x-axis tidak jalan
|
Periksa atau ganti driver unit
|
323
|
Frame y-axis tidak jalan
|
Periksa atau ganti driver unit
|
331
|
Bobbin charger tidak normal
|
Periksa/seting bagian bobbin canger
|
352
|
Fungsi sequin tidak normal
|
Periksa sequin card atau ganti
|
382
|
Color change tidak bergerak
|
Periksa Sensor posisi jarum
atau ganti motor color change
|
383
|
Signal untuk pergantian warna tidak ada
|
Periksa potensiometer(posisi sensor jarum)
|
384
|
Signal sensor ganti warna tidak ada
|
Periksa photo-interrupter
|
3A1
|
Penggerak potong benang tidak ada signal
|
Priksa atau ganti join card
|
3A6
|
Posisi pisau potong benang tidak benar
|
Periksa posisi sensor pemotong benang /movable knife
|
3A8
|
Tread holding driver tidak ada signal
|
Periksa head card
|
3B5
|
Signal antara CPU card dan panel card,CPU card
Dan inverter, atau di antara CPU card, join card, dan head card tidak ada
|
Matikan mesin dan periksa sambungan kabel
Di antara card_card tersebut
|
3D1
|
Volt battery lemah
|
Nyalakan mesin kemudian seting parameter dan masukan designs
|
3D3
|
Power supply tidak normal
|
Periksa sambungan kabel
atau ganti transformer
|
3D4
|
Data check sum tidak terdeteksi
|
Ganti CPU cardnya
|
3D5
|
A ram data check sum tidak normal
|
Install ulang program system mesinnya kalau masih ada atau perbaiki panel cardnya
|
B01
|
Waktu memasukan type format disket salah
|
Format ulang dengan type kapasitas yang benar
|
B02
|
Merekam disket dari mesin tidak bisa masuk
|
Coba lagi kalau tetap ngga bisa coba ganti pakai disket yang lainnya
|
B03
|
Protect disket aktif
|
Buka protect diketnya
|
B04
|
Disket tidak di pasang di fdd
|
Masukan disketnya
|
BC1
|
Data disket tidak terbaca
|
Ganti dengan designnya yang lain
|
BC2
|
Waktu merekam design ke mesin sudah ada yang sama
|
Ganti nama designnya
|
BC4
|
Design yang di rekam ke disket tidak ada
|
Rekam ulang
|
BC5
|
Kapasitas disket sudah penuh
|
Pakai disket yang baru
|
C01
|
Fdd ada masalah
|
Periksa kabelnya atau kalau Fddnya rusak ganti dengan yang baru.
|
No comments:
Post a Comment